One (1) 2002 VACTOR Hydro-Excavator, EQ# 2971, having 2-stage centrifugal fan with auxiliary engine, 12 cubic card debris hopper and 1300 gallon water capacity, equipped with the following:
E-mail: websales@dohenysupplies.com
URL: http://www.dohenysupplies.com/vacuum-truck
Debris Body
12 Cubic yard volumetric debris body
Cylindrical design, 1/4" abrasion & corrosion resistant Ex-Ten steel
Flat style, 3/4 rear door, hinged at top w/replaceable neoprene seal
Hydraulic rear door locking system with door grabber
Hydraulic rear door open & close system
6" Knife valve with 10' drain hose, cam-loc connector
Rear door support for operator safety
Font mounted hydraulic dump cylinder, 50 degree dump angle, power up/power down
Dual air ports with dual 10" stainless steel float ball shutoff system/stainless steel screens
Water Tanks
1300 Gallon capacity - #304 3/16" stainless steel water tank
Water tank separate from debris tank
Includes anti-siphon device & anti-splash valve w/25' water fill hose and connectors
Water level sight gauge, Mark III electronic low water warning system
10 Year warranty against corrosion and cracking
Water System
Water system rated design is 13gpm @ 2500 psi
Hydraulic operated Tri-plex piston water pump
Water pump on/off located on pendant control and control box
Variable pressure and flow achieved by electronic-over-hydraulic controls at operators station
Handgun hose 3/8" x 75' w/operating pressure of 3500 psi and burst pressure of 14,500 psi, located in heated cabinet.
Fan Vacuum System
Dual 38" aluminum two-stage centrifugal compressor/fan system
Hydrostatic fan drive system
Gauge package: voltmeter, water temperature, oil pressure, tachometer w/hourmeter located at operator station
2" Fan housing drain
Vacuum relief located in the inlet of debris tank to allow operator to vent to atmosphere. Pendant control operated.
Remote push button pendant control w/75' cable with a vacuum relief, water on/off and throttle control
Control Panel (Located Passengers Side)
Located inside an aluminum box for protection
The control panel will include:Chassis Engine tachometer w/hourmeter, Blower tachometer,Blower temperture gauge, Mark III electronic low water indicator, circuit breakers, water pump on/off, Vacuum gauge, water pump pressure control
Joystick boom control at operator's station
Boom & Vacuum Hose
8' Hydraulic telescoping boom - 180 degree rotation
8" I.D. wire reinforced rubber suction hose
Boom will have an electric-over-hydraulic solenoid system with speed flow control valves
Boom will be powered hydraulically up/down/right/left/extend/retract
Boom control, joystick and hand carried pendant control w/75' cable located at operator station
All boom inlet hose and tubing will be 8" inside diameter
Vacuum Pipe Package
Package will be 1- 8" x 7' aluminum fluidizer tube w/rubber safety end; 2 - 8" x 5 aluminum flanged pipe; 1 - 8" x 7' aluminum flanged pipe; 4 - 8" quick clamps
All connections between debris body and vacuum system will be self-adjusting, pressure fitting type
Water System/Pipe Package
Includes 1 - Digging wand, 1 - dual nozzle assembly, 1 - triple nozzle assenbly, quick couplers and shut-off valve, 3 - Extension pipe assemblies totaling 20 Ft.
Water Heater
Water heater will be rated at 400,000 B.T.U.
12 Volt heater will have no flow/burner shutdown, electronic temperature control, heater inlet pressure gauge, LED temperature display
Hydraulic System
Hydraulic reservoir capacity of 65 gallons w/strainers on all suction lines.
Oil level sight gauge
Inspection hatch for maintenance
10 micron spin on type filter
Electrical
Entire system will be moisture and vapor sealed
Electrical connections require no exposure wires or terminals
Light bulbs will be shock mounted
Complete wiring diagram is provided with machine, circuit breakers are supplied
Storage Cabinets
1 - 50" x 30" deep x 24" high aluminum tool box located right behind cab/water pump and hose retractable handgun reel will be located in this box, box will be heated.
Mounting
Approved truck chassis
Paint
All metal surfaces shot blasted prior to painting
All metal surfaces will be phosphate washed prior to painting
Coated with a minimum of 2.5 mil primer
Painted with a minimum of 2.5 mil finish paint process
Module components will be painted prior to assembly
Miscellaneous
Tow hooks front and rear
Mud Flaps
Electronic back-up alarm
Fenders
Body: White
Chassis: White
2002 Sterling Chassis
|
